To plan a large wood-look aluminum siding or ceiling project, start with accurate square footage for every surface, pick one panel profile and finish per area, and turn those numbers into a piece count and a planning budget before anyone orders material. On a 1,000 to 2,000+ square foot job, small decisions like board direction, trim, and where the panels stop add up fast, so settle them on paper first. Then send photos and measurements for an exact quote and see real samples in your light.
Big projects are where woodgrain aluminum makes the most sense, because covering a whole façade or a large lanai ceiling with real wood in South Florida humidity, sun, and salt air means a big maintenance bill later. Perfal panels are aluminum, manufactured in Brazil and sold in the US by Perfal USA, and they are fire, weather, fade, warp, rot, and bug resistant. Here is how homeowners, designers, architects, and builders can plan a project of this size without surprises.
Step 1: Measure Every Surface, Not Just the Main Wall
Large projects are almost never one rectangle. A typical scope might combine a front façade, the soffits around the roofline, a covered patio ceiling, and an accent wall by the pool. Measure each one separately and write it down by area:
Walls and façades: width times height for each wall section, then subtract big openings like garage doors, sliders, and large windows.
Ceilings and soffits: length times depth for each run. Soffits are long and narrow, so a small mistake in depth multiplies over the full perimeter.
Accents: pergola walls, outdoor kitchen islands, fences, and privacy screens each get their own line.
Keep the areas separate even if they will use the same finish. It makes the quote easier to check and helps your installer plan the cuts.
Step 2: Choose a Profile for Each Area
The panel profile changes both the look and the budget, and on a large job the difference is significant. Perfal offers three cladding profiles, plus a standalone panel for fences and dividers:
Slats: a triple-slat panel with layered reveals. It reads as individual wood boards and is the signature Perfal look for slat walls, façades, and ceilings.
Slim: a flat, minimalist panel with a smooth face and no slat lines. It is great for walls and ceilings and comes in Mahogany and Studio White.
Single: one wider slat per panel, our lightest panel, for a bold continuous look.
Standalone: a double-walled panel for free-standing fences, dividers, and outdoor shower walls.
Many large projects mix profiles on purpose. A common approach is Slats on the feature wall people see first, and Slim on the soffits and ceilings where a calm, flat plane looks cleaner. Slim and Single also price lower per square foot than Slats. You can see every profile and finish with photos on our catalog page.
Step 3: Pick Finishes With the Whole House in Mind
On a small accent wall you can pick a finish you love and stop there. On 1,500 square feet, the finish becomes part of the architecture. Perfal has two woodgrain finishes, Mahogany and Golden Oak, made with a woodgrain film over a specialty sublimation powder coating, and two solid powder-coated colors, Studio White and Matte Black. The solid colors are the more cost-effective options.
A few planning tips:
Repeat a finish, don't scatter them. One wood tone carried across the façade, soffits, and patio ceiling looks intentional. Three different finishes on one house usually looks busy.
Use solid colors where they work hardest. Studio White on long soffit runs or a large ceiling keeps the space bright and keeps the budget in check, while a wood tone does the heavy lifting on the feature wall.
Look at samples outside. Wood tones look darker in shade and under a roof than in direct sun. Hold samples against your stucco, roof, and trim colors at different times of day.
For bulk orders, every profile is available in any of our colors, and custom colors can be special-ordered with a 2 to 3 month lead time. If a custom color is on the table, decide early so it does not hold up the schedule.
Step 4: Turn Square Footage Into a Piece Count
Perfal panels are priced and sold per piece. Each piece is 236.625 inches long, about 19.72 feet. To estimate how many pieces you need, divide your area by the coverage of one piece for your profile. Based on each profile's nominal width, one piece covers roughly:
Slats: about 8.3 square feet
Slim: about 9.7 square feet
Single: about 8.6 square feet
So 1,600 square feet in Slats works out to roughly 193 pieces before cuts, and about 166 pieces in Slim. Every project also needs extra material for cuts around windows, corners, fixtures, and the ends of runs. Your installer will set that allowance based on how complex the layout is. Treat these numbers as a sanity check, and we will confirm the exact count from your plans or photos.
Two layout decisions affect the count and the look:
Board direction. Horizontal boards make a façade feel wider and lower. Vertical boards make it feel taller. On ceilings, running boards away from the house pulls the eye outward. Pick a direction per area and keep it consistent.
Where seams land. With pieces close to 20 feet long, many walls and soffit runs can be covered without a mid-run joint. Plan around the 20-foot length and you get fewer seams and less waste.
Step 5: Plan Trim, Corners, and Fixtures Before Ordering
Trim is the part of a large project people forget to count. Every outside corner, inside corner, and transition needs a finishing piece. Perfal makes matching 1 inch and 3/4 inch corner trims and a T trim in the same finishes as the panels. Walk the house and count every corner and edge by length, the same way you measured the walls.
Also mark the things that go through the panels: light fixtures, ceiling fans, outdoor speakers, cameras, hose bibs, dryer vents, and electrical boxes. On a big ceiling or soffit, decide fixture locations first so the board pattern stays even around them. Perfal panels use a tongue-and-groove system, and the screws on each panel are covered by the next one, so a clean layout makes the finished surface look seamless.
Step 6: Build a Planning Budget
Once you know the area, profile, and finish, our Project Estimator gives you a working number in seconds. These examples use the estimator's rates on 1,600 square feet. They are planning estimates, not quotes, and corner trim and finishing pieces are quoted separately:
Slats in Mahogany, materials only: about $20,465 to $23,266
Slim in Studio White, materials only: about $13,192 to $14,997
Slats in Mahogany, installed, moderate complexity: about $34,905 to $39,682
Installed estimates change with complexity. A single-story home with flat wall runs costs less to install than a multi-story façade with lots of corners and cutouts. Final pricing depends on an on-site or photo-based assessment.
Large orders can also qualify for better pricing. Bulk discounts run 5% to 15% depending on total tonnage, starting at 2 tons, and contractors get a discount regardless of tonnage. If you are a builder or remodeler buying for multiple jobs, look at our Trade Program.
Step 7: Line Up Permits, Installer, and Schedule
Exterior siding and soffit work on a South Florida home usually needs a building permit, and many Florida building departments ask for product documentation and installation instructions with the application. Requirements vary by city and county, so check with your local building department or let your contractor handle it. Ask us early what documentation is available for your product so paperwork does not hold up your start date.
A few more things to settle before ordering:
Who installs. Decide whether you are buying materials only for your own installer or want installation coordinated. The estimator lets you compare both.
Substrate and framing. Ceilings and soffits need solid framing or furring at the right spacing, and existing walls may need repair before panels go on.
Delivery and storage. Twenty-foot pieces need a clear path from the truck and a flat, protected spot on site.
When you request a quote, we reply with pricing, lead time, and shipping for your project, usually within one business day.
What to Send for an Accurate Quote
The fastest way to a real number on a large project is to send everything at once:
Square footage by area (walls, soffits, ceilings, accents)
The profile and finish you are leaning toward for each area
Photos of each elevation and any ceiling or soffit you are covering
Plans or a dimensioned sketch, if you have them
Materials only or installed, and your city
Your target start date
If you are still deciding on the look, these guides can help: covered patio and soffit ceilings in Florida compares ceiling materials, and our Florida porch ceiling ideas cover color, board direction, and lighting.
FAQ
How much does it cost to cover 1,500 square feet with wood-look aluminum siding?
It depends on the profile, finish, and whether you want installation. Enter 1,500 in our Project Estimator to see a planning range for each option. Wood-tone finishes cost more than solid colors, and installed pricing changes with complexity.
How many panels do I need for 2,000 square feet?
Divide the area by the coverage of one piece: roughly 8.3 square feet for Slats, 9.7 for Slim, and 8.6 for Single. That is about 241 Slats pieces or about 208 Slim pieces before cut waste. We confirm the final count from your plans or photos.
Can I mix profiles and colors on one house?
Yes. A common plan is a wood-tone Slats feature wall with Studio White Slim on the soffits and ceilings. Keep it to one or two finishes so the house looks intentional.
Do you give a discount on large orders?
Yes. Bulk discounts run 5% to 15% depending on total tonnage, starting at 2 tons, and contractors get a discount regardless of tonnage.
Can I see the finishes before I commit to a big order?
Yes. Request a sample box, or schedule a product drop-off by appointment in Palm Beach and Broward counties.
See the Finishes Before You Plan the Whole House
On a project this size, seeing the real panels in your own light is the best decision you can make before ordering. Request a sample box with our wood-look and solid finishes, or call us at (561) 933-6653 to talk through your measurements. We work with homeowners, designers, architects, and builders across Delray Beach and South Florida.